manualshive.com logo in svg

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 241 / 304

Поделиться
Скачать
Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 241

●

Confirm with <F3 Edit variable>.

●

Enter the new value and confirm.

A wrong entry is answered with a warning message.

The value "NUL" is assigned to a variable if the content was deleted

with <Backspace> or <Delete> and no new characters or values

were entered.
The value "NUL" cannot be assigned to permanent variables.

Breakpoints on variables

If a breakpoint is set on a variable, the execution of the NC program is stopped

in the following cases:
●

If the program line which contains operations with this variable is reached.

●

If the value of the variables changes, for instance by setting values in the

NC program.

If the variables set on a breakpoint are displayed in the List breakpoints .
For each variable, two modifications can be configured:
●

"Write" mode

●

"Read-only" mode

Fig.11-5:

Breakpoints on variables

In "Read-only" mode, the program execution is interrupted when the variable

was read, for instance in the NC program (visible in the "Program window").
The following message box informs the user of a program interruption triggered

by a breakpoint on a variable:

(#121) The breakpoint on the variable <VariableName> has been reached. Access mode: Write!

DOK-MTX***-NC*OP***V11-AP01-EN-P 
Rexroth IndraMotion MTX 11VRS Standard NC Operation 

Bosch Rexroth AG

239/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов