Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 234

Страница: 234 / 304

●

Active keys are shown with white lettering

●

Keys that are inactive, e.g. because of a configured option, are grayed

out.

The assignment of the F-keys change depending on the active window in the

workspace (see the following figure).
Select a window by:
●

clicking on it with the mouse

●

using the F-key (<F7 Next window> it is possible to browse through the

windows one by one

●

using the F-key <F2 Navigation> in the lower F-keypad, a certain window

can be selected.

F-keypad

<F2>

<F3>

<F4>

<F5>

<F6>

<F7>

<F8>

<F9>

1. Level

Channel

selection

Save work‐

space

Load work‐

space

Breakpoint

list

Debug

mode / re‐

set mode

Enable

window

Reset

properties

Close Ana‐

lyzer

Variable level

Navigation Set break‐

point

Quick‐

Watch

Add to

watch

Zoom +/-

Next Win‐

dow

Extend/

Close sub‐

structure

Back

Watch/QuickWatch lev‐

Navigation Edit varia‐

ble

Delete

watch

Delete all

variables

Zoom +/-

Next Win‐

dow

Extend/

Close sub‐

structure

Back

1. Program level

Navigation Set/delete

breakpoint

Activate/

deactivate

breakpoint

Continue

step mode/

mode

Zoom +/-

Next Win‐

dow

Next level Back

2. Program level

Find...

Delete all

break‐

points

Activate all

break‐

points

Open sub‐

routine

Open ac‐

tive pro‐

gram

One level

back

Back

Stack level

Navigation

Go to Start Zoom +/-

Next Win‐

dow

Extend/

stack

Back

Output level

Navigation

Delete out‐

put

Zoom +/-

Next Win‐

dow

Back

File level

Navigation Subdirec‐

tory

Superordi‐

nated di‐

rectory

Display file Zoom +/-

Next Win‐

dow

Update

files

Back

Finding Text

The "Program" window can find an alphanumeric character string in the dis‐

played NC program on the 2nd level via the F-key (<F2 Find>).

Resetting Window Properties

The changeable window width can be reset any time to the fixedly stored values

using the mouse. With <F8 reset properties> in the topmost F-keypad, the de‐

fault values can be enabled again.
Resetting the window properties does not affect breakpoints or selected vari‐

ables.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

232/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 234 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: