Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 229

Страница: 229 / 304

Extended Functionality

11.1

NC-Analyzer

11.1.1

Overview

Purpose of the NC-Analyzer

The NC-Analyzer can be used to test NC programs and swiftly find program‐

ming errors.
The NC-Analyzer is part of the MTX interface.

Properties of the NC-Analyzer

The NC-Analyzer
●

is applicable to programs in CPL format (Customer Programming Lan‐

guage) and DIN 66025 format

●

includes subroutine programming

●

includes editor functions for executable programs

●

supports all CPL variable formats

●

supports multidimensional CPL variables (arrays)

●

supports local, global as well as permanent variables

●

can set breakpoints on NC blocks (maximum of 20 active at the same time)

●

can set breakpoints on variables

●

can change variables values at program runtime

●

can automatically watch up to 40 active variables at the same time

Error Search in the Program

The NC-Analyzer answers for example the following questions:
●

Where did the error occur for the first time in the program?

●

What are the effects of the error on the program?

●

What are the effects on other variables or program parts?

●

How severe is the error for the program?

The NC-Analyzer allows to systematically select all relevant variables and track

their contents step by step at program runtime.
Setting breakpoints allows the program to stop at user-defined points at runtime

to request the values of individual variables and check monitored variables for

their contents.
At a breakpoint, other values can be assigned to each variable. This facilitates

testing of a different processing scenario in the program. In case of an incorrect

variable assignment by the program, this variable can be experimentally as‐

signed with the "correct" value.
The nested structure of main programs and subroutines can be seen and moni‐

tored in the "Stack" window.
User-specific messages (MSG, GMSG,..) in the "Output" can be used to test

the program run.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

227/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 229 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: