Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 215

Страница: 215 / 304

10.6

MTX System Status

10.6.1

Introduction

The MTX system status is a commissioning application and diagnostic appli‐

cation for PC-based MTX controls.
This application controls, monitors and visualizes the state of the following

component groups:
●

MTX standard

●

MTX performance

●

MTX advanced

The MTX system status is embedded in the diagnostic display and can be

opened via <F5>after calling the diagnostic display with <OP9>.
After calling the application, it is displayed as shown below.

Fig.10-36:

MTX system status

The MTX system status is divided into 3 sections.
In the upper section "Properties", you can find general information on:
●

Name:
The name configured for the respective control in the IndraWorks Engi‐

neering is displayed.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

213/301

Diagnostics

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 215 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: