Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 162

Страница: 162 / 304

Fixed area

Frozen area

Scrollable area

Fig.8-1:

Screen layout of a tool list

Functions of the table areas.

fixed area:

no cursor navigation

possible

Always visible

frozen area:

cursor navigation pos‐

sible

Always visible

scrollable area:

cursor navigation pos‐

sible

not always visible

Structure Tool Editor

Overview

Like the NC main screens, the tool editors function according to the ACI appli‐

cation (Active-Container-Interface).
This means
●

it is freely configurable.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

160/301

Tool Management

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 162 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: