Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 140

Страница: 140 / 304

7.4.2

General Structure of the Editor to Define SD Variables

Editor structure

Fig.7-12:

Editor structure

The editor consists of a list with six columns:
●

Identifier

●

Type

●

Memory type

●

Dimension

●

Init

●

Comment

Input options in the individual col‐

umns

Each column has its individual input options. There are freely editable input

fields and predefined selection lists.
●

Identifier
–

Freely editable SD variable name.

●

Type
–

Selection from a list of all data types defined in the schema files.

●

Memory type
–

Selection between volatile and permanent.

●

Dimension
–

Selection between Channel, Drive and Spindle or

–

freely editable dimension.

●

Init (no entry)
–

Information whether there is an initialization value defined for the

variable in the "SDdatxxx.xml" file.

●

Comment
–

freely editable comment

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

138/301

Programming

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 140 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: