Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 130

Страница: 130 / 304

After pressing "Ok", a menu opens in which you specify the storage location

and the name of the export file with the extension "*.ncc".

Fig.7-5:

File name selection

In the export file created "*.ncc", all available files from the desired range can

be saved.

Import Cycles

After pressing the F-key <F5 Import cycles, a menu is opened in which the file

to be imported (previously exported) with the extension "*.ncc" is selected.

Fig.7-6:

Selecting the cycle import file

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

128/301

Programming

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 130 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: