manualshive.com logo in svg

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 119 / 304

Поделиться
Скачать
Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 119

Edit - Copy (Block)

Keyboard shortcuts

<Ctrl>+<C>
The highlighted section is copied into the clipboard.

Edit - Paste (Block)

Keyboard shortcuts

<Ctrl>+<V>
The text contained in the clipboard is pasted into the NC program at the current

cursor position.

Edit - Select Line

The current line is selected.

Edit - Select All

Keyboard shortcuts

<Ctrl>+<A>
The entire NC program is selected.

7.2.4 

Functions under Navigate...

Edit - Search

Keyboard shortcuts

<Ctrl>+<F>
A specifiable character string can be sought for in the entire program. You can

select upper case or lower case as well as the direction of the search.
If the "Replace" button is pressed after a character string is entered, the string

can be replaced by another one. If the search dialog is closed, you can continue

to search within the program using keyboard shortcut <Ctrl>+<R>.

Edit - Next Error

Moves the cursor to the next error registered and marks the location.
The corresponding error message is additionally displayed in the status bar.

The error message can be hidden using <Esc>.
The function is only available if at the moment of opening the editor, errors /

warnings existed for this program respectively new errors are registered after

saving with reselection or after following NC simulation.

Edit - Previous Error

Moves the cursor to the previous error registered and marks the location.
The corresponding error message is displayed additionally in the status bar.

The error message can be hidden using <Esc>.
The function is only available if at the moment of opening the editor, errors /

warnings existed for this program respectively new errors are registered after

saving with reselection or after following NC simulation.

Edit - Go to Beginning of File

Keyboard shortcuts

<Ctrl>+<Home>
Moves the cursor to the beginning of the file.

Edit - Go to End of File

Keyboard shortcuts

<Ctrl>+<End>
Moves the cursor to the end of the file.

DOK-MTX***-NC*OP***V11-AP01-EN-P 
Rexroth IndraMotion MTX 11VRS Standard NC Operation 

Bosch Rexroth AG

117/301

Programming

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов