Bosch Rexroth Indramat ECODRIVE DKC02.1 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 88

background image

ECODRIVE DKC02.1 Drive Controller

Safety instructions for electrical drives

2-1

DOK-ECODRV-DKC02.1****-PRJ2-EN-P

2

Safety instructions for electrical drives

Please read the following instructions carefully before initial startup.
These safety instructions must be observed at all times.

If the product is transferred to a third-party, the safety instructions must be
included.

WARNING

Improper use of this equipment and non-compliance
with the safety instructions provided can result in
damage, personal injury or, in extreme cases, death.

2.1 General

INDRAMAT GmbH is not liable for any damages resulting from failure
to observe the safety instructions in this document.

•

Documentation in the relevant national language should be obtained
before initial startup if the language in this documentation is not per-
fectly understood.

•

Proper transport, correct storage, assembly, and installation as well as
care in operation and maintenance are prerequisites for optimum and
safe operation of this equipment.

•

Qualified personnel:

Only qualified personnel should be permitted to operate this equipment
or work in its immediate vicinity. Personnel is considered qualified if it
has sufficient knowledge of the assembly, installation, and operation of
the product as well as all warnings and precautionary measures in this
documentation.

Furthermore, personnel should be trained, instructed or authorized to
switch electrical circuits on and off and to ground and mark them in
accordance with the requirements of safety engineering. Personnel
should possess adequate safety equipment and be trained in first aid.

•

Use only replacement parts approved by the manufacturer.

•

All safety regulations and requirements for the specific application
must be followed.

•

The equipment is designed to be installed in machines for commercial
use.

•

Startup is only permitted once it is sure that the machine in which the
products are installed complies with the requirements of the national
safety regulations and safety specifications of the application.
European countries: EC Directive 89/392/EEC (Machine Guideline)

•

Operation is only permitted if the national EMC regulations for the spe-
cific application have been met.
European countries: EC Directive 89/336/EEC (EMC Guideline)

The instructions for installation in accordance with EMC requirements
can be found in the document "EMC Drive and Control Systems."

The responsibility for adherence to the limiting values required by na-
tional regulations lies with the manufacturer of the equipment or ma-
chine.

•

Technical specifications as well as the connection and installation re-
quirements can be found in the product documentation and must be
observed under all circumstances.

LSA Control S.L. www.lsa-control.com [email protected] (+34) 960 62 43 01

«
...
11
12
13
14
15
...
»

Содержание Rexroth Indramat ECODRIVE DKC02.1 Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth Indramat ECODRIVE DKC02.1 Series

Бренд: zipwake Страницы: 12

Бренд: Watts Страницы: 2

Бренд: jbc Страницы: 12

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: BEIER-Electronic Страницы: 22

Бренд: Baby Trend Страницы: 10

Бренд: GBD Страницы: 68

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: National Instruments Страницы: 2

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: Aurora Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды