Bosch Rexroth IndraDrive HMS02 Скачать руководство пользователя страница 47

Страница: 47 / 71

●

Position the cooling unit in such a way that the blower of the cooling unit

does not spray accumulated condensation water onto the devices in the

control cabinet. Mount the air duct in the control cabinet accordingly.

Cooling Unit on Top of the Control Cabinet

Cooling Unit at the Front of the Control Cabinet

Cooling unit

Interior of control cabinet

Air duct (protects devices against condensation water)

Device in control cabinet

Fig.5-19:

Arranging the Cooling Units

Avoiding Moisture Condensation

Moisture condensation occurs when the temperature of the device is lower than

the ambient temperature.
●

Set cooling units with temperature adjustment to the maximum surround‐

ing temperature and not lower!

●

Set cooling units with follow-up temperature in such a way that the interior

temperature of the control cabinet is not lower than the temperature of the

surrounding air. Set the temperature limitation to the maximum surround‐

ing temperature!

●

Only use well-sealed control cabinets so that moisture condensation can‐

not arise as a result of warm and moist external air entering the cabinet.

●

In the event that control cabinets are operated with the doors open (com‐

missioning, servicing etc.), it is essential to ensure that after the doors are

closed the drive controllers cannot at any time be cooler than the air in the

control cabinet. For this reason, sufficient circulation must be provided

inside the control cabinet.

Bosch Rexroth AG

DOK-INDRV*-HMS02*UL***-IB03-EN-P

Rexroth IndraDrive Drive Controllers Power Sections HMS02

44/67

Instructions for Use

Содержание Rexroth IndraDrive HMS02








































































Результаты поиска

Содержание Rexroth IndraDrive HMS02

Отзывы:

Похожие инструкции для Rexroth IndraDrive HMS02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive HMS02, Инструкция по эксплуатации

Результаты поиска

Содержание Rexroth IndraDrive HMS02

Отзывы:

Похожие инструкции для Rexroth IndraDrive HMS02

Бренды по названию

Популярные бренды