Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 87

Страница: 87 / 344

Components marked with gray background color: Optional, de‐

pending on the application; the choke is used to reduce current

harmonics

Component HCS01 (more powerful than component B); con‐

nected to other components via DC bus

Component HCS01 (less powerful than component A); connec‐

ted to other components via DC bus

Bb relay contact wiring

Module bus

Fig. 4-26:

Parallel operation

Connect the Bb relay contacts of all supplying components in ser‐

ies. You thereby ensure that the mains contactor is switched off in

case there is an error in a component.

Mains connected load and mains current

Technical data of the components

●

See

chapter 7.3.2 "Mains voltage" on page 233

●

See

chapter 7.3.3 "DC bus" on page 240

Calculating the mains-side phase current

The mains-side phase current is required for the following cases:
●

Selecting mains contactor

●

Determining fuses in the mains connection

●

Determining line cross section

●

Selecting other components in the mains connection (mains filter, mains

choke)

Operation under rated conditions

For data on mains contactor, fuses and cross section in operation under rat‐

ed conditions, see technical data of the respective component.

Operation at partial load

Operation at partial load can lead to smaller mains contactors, fuses and line

cross sections.
If defined data for operation at partial load are available, the mains-side

phase current can be determined as follows:
1.

Determine motor power
Take power of drive controller-motor combination from Rexroth Indra‐

Size or calculate it.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

85/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды