Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 77

Страница: 77 / 344

Looping through the control volt‐

age

Property damage in case of error from line

cross section being too small!

NOTICE

Observe the current carrying capacity of the connection points for control

voltage supply at the components used.

You may only loop through the control voltage between the components,

when the sum of current consumptions ΣI

of the individual components is

smaller than 10 A (current carrying capacity of the connection point X13).

Fig. 4-15:

Looping through the control voltage

Sample calculation for 3 drive controllers:

Fig. 4-16:

Continuous current

The result I

has to be smaller than the specified current carrying capacity of

the connection point.

4.6.3

Mains connection

Residual-current-operated circuit breakers (RCD, RCCB) as additional fusing

General information

The following designations are used for residual-current-operated circuit

breakers:
●

RCCB (Residual-Current-Operated Circuit Breaker)

●

RCD (Residual-Current-Operated Device)

●

RCM (Residual-Current Monitoring Device)

●

Earth-leakage circuit breaker (voltage-independent)

●

Residual-current circuit breaker (voltage-dependent)

It is only to a limited extent that residual-current-operated circuit

breakers can be used with Rexroth IndraDrive Cs systems.

If these circuit breakers are to be used, the company erecting the installation

has to check the mutual compatibility of the residual-current-operated circuit

breakers and installation or machine with the drive system, in order to avoid

accidental triggering of the residual-current-operated circuit breaker. This has

to be taken into account

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

75/341

Rexroth IndraDrive CsDrive Systems with HCS01

Combining the individual components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды