Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 183

Страница: 183 / 344

Technical data of the components

7.1

Control section

7.1.1

EC - standard encoder evaluation

Supported encoder systems

Encoder systems with a supply voltage of 5 and 12 V:
●

MSM motor encoder

●

MS2N motor encoder

●

MSK motor encoder

●

sin-cos encoder; HIPERFACE®

●

sin-cos encoder; EnDat 2.1; EnDat 2.2

●

sin-cos encoder; with reference track

●

5V TTL square-wave encoder; with reference track

●

SSI

●

Combined encoder for SSI (combination of SSI and 1V

sin-cos encod‐

er)

●

Resolver (resolvers are not supported if optional "Safe Motion" safety

technology is also in use)

●

Hall sensor box SHL02.1

●

Digital Hall sensor in conjunction with Hall sensor adapter box SHL03.1

Encoder type

IndraDyn S MSM motors (5V supply voltage)

Properties

Encoder systems of the MSM motors are digital encoder systems that can be

evaluated in absolute form.
The optionally available battery box (SUP-E0x-MSM-BATTERYBOX) facili‐

tates the multi-turn functionality.

Connection diagram

Line cross section ≥ 0.5 mm²; observe allowed encoder cable

length

Line cross section ≥ 0.14 mm²

Fig. 7-1:

EC connection diagram with encoder system of IndraDyn S MSM

motors

For direct connection to the encoder system, use our RKG0033 or

RKG0062 cable.

Power supply

5 V (the voltage is made available via the EC interface)

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

181/341

Rexroth IndraDrive CsDrive Systems with HCS01

Technical data of the components

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды