Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 344

background image

X77, L+ L-, DC Bus Connection

Lethal electric shock by live parts with more

than 50 V!

WARNING

Before working on live parts: De-energize installation and secure power

switch against unintentional or unauthorized re-energization.
Before accessing the device, wait at least 30 minutes after switching off the

supply voltages to allow discharging.
Check whether voltage has fallen below 50 V before touching live parts!
Never operate the drive controller without touch guard or without DC bus con‐

nector. Only remove the touch guard, if you want to use the DC bus connec‐

tor at the drive controller. If you do not use the DC bus connector any longer,

you have to cover the DC bus connection with the supplied touch guard.

Observe the information on DC bus coupling (see

"DC bus coupling" on page 105

Function, Pin Assignment

The DC bus connection connects
●

several HCS01.1E-W00xx-x-03 to each other

●

one drive controller to a DC bus capacitor unit (to backup the DC bus

voltage)

Touch Guard

The DC bus connection has been provided with a touch guard at the factory.

To plug the DC bus connector, you have to remove the touch guard.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

151/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

«
...
151
152
153
154
155
...
»

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: K&K Страницы: 6

Бренд: Idesco Страницы: 11

Бренд: B meters Страницы: 2

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Harmonic Drive Страницы: 25

Бренд: Nelson Страницы: 8

Бренд: JANE Страницы: 144

Бренд: Universal Remote Страницы: 20

Бренд: Ublox Страницы: 58

Бренд: Vector Страницы: 10

Бренд: ARI-Armaturen Страницы: 17

Бренд: Combi Страницы: 20

Бренд: Hasco Страницы: 78

SWD Starter Kit

Бренд: ez-wheel Страницы: 30

Бренд: Ariston Страницы: 97

ACCUVALVE AVC6000

Бренд: Accutrol Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды