Bosch Rexroth IndraDrive CsDrive System with HCS01 Скачать руководство пользователя страница 119

Страница: 119 / 344

Condition as supplied, identification, transport and

storage

5.1

Condition as supplied

5.1.1

Factory testing

Voltage testing and insulation resistance testing

According to standard, the components of the Rexroth IndraDrive Cs range

are tested with voltage.

Testing

Test rate

Voltage testing

100% (EN 61800-5-1)

Insulation resistance testing

100% (EN 60204-1)

Tab. 5-1:

Applied standards

5.1.2

Customer testing

Risk of damage to the installed Rexroth com‐

ponents by customer-side testing of the ma‐

chine or installation!

NOTICE

Before conducting voltage testing or insulation resistance testing for an instal‐

lation or machine in which these components are used:
Disconnect all connections to the Rexroth components or disconnect the

plug-in connections to protect the electronic components.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

117/341

Rexroth IndraDrive CsDrive Systems with HCS01

Condition as supplied, identification, transport and storage

Содержание Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive CsDrive System with HCS01, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive CsDrive System with HCS01

Отзывы:

Похожие инструкции для Rexroth IndraDrive CsDrive System with HCS01

Бренды по названию

Популярные бренды