Bosch Rexroth IndraControl XFE01.1-SY-01 Скачать руководство пользователя

Страница: 42 / 52

The front panel is dissolved by solvents!

NOTICE

●

Do not use any solvents (e. g. diluents) for cleaning!

Maintenance notes
The Safety extension module IndraControl XFE01.1-SY-01 runs without

maintenance. Check the Safety extension module IndraControl XFE01.1-SY-01 at

least annually. The check includes:

●

Correct position of the extension module

●

Correct position of all plug connections and terminal connection

●

Damage or rupture

Replace the extension card IndraControl XFE01.1-SY-01 immediately if damaged.

In case of damages, please contact the Bosch Rexroth Service.
Replacing memory card

Unintended exchange of the memory card can
damage

the

Safety

extension

module

IndraControl XFE01.1-SY-01

NOTICE

Only qualified service personnel is allowed to exchange the memory card.

For the position of the memory card, refer to

fig. 12-1 "Safety extension module

IndraControl XFE01.1-SY-01" on page 31

To replace the memory card, proceed as follows:

1. Disconnect the complete system from voltage. This includes the

IndraControl XMxx control. The Safety extension module IndraControl

XFE01.1-SY-01 is connected to this control.

2. Secure the system against restart.
3. Press the microSD card down into the microSD slot down until the

microSD card disengages.

4. Remove the microSD card from the slot.
5. Insert the new microSD card into the slot with the labeling up.
6. Press the microSD card down into the slot down until the microSD card

engages.

7. Check whether the microSD card correctly engaged into the slot.
8. Commission the system again.

36/45
Maintenance

IndraControl XFE01.1-SY-01 Safety Ex-

tension Module

Bosch Rexroth AG R911376654_Edition 03

Содержание Rexroth IndraControl XFE01.1-SY-01





















































Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl XFE01.1-SY-01, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды