Bosch Rexroth IndraControl XFE 01.1 Series Скачать руководство пользователя страница 11

Страница: 11 / 36

11 / 36

IndraControl XFE 01.1

Voltage supply and current consumption

Bosch Rexroth AG

R911345570, Edition 06

NOTICE

Failure of the product due to contaminated air

−

The ambient air must not contain acids, alkaline solutions, corrosive

agents, salts, metal vapors and other electrically conductive contami-

nants in high concentrations

−

The devices to be installed into the housing and installation compart-

ments must at least comply with the degree of protection IP

according to DIN EN 60529.

−

The device shall be provided in a suitable fire enclosure in the end-use

application.

NOTICE

Defective product due to gases jeopardizing functions
Due to the risk of corrosion, avoid sulphurous gases (e.g. sulphur dioxide

(SO

) and hydrogen sulphide (H

S)). The product is not resistant against

these gases.

NOTICE

Failure of the product due to overheating
To avoid overheating and a trouble-free operation of the product, the ambient

air has to circulate. Also refer to the section “Installation notes”.

This is a product that corresponds to the limit values of the emitted interference of class A

(industrial environments). This is a product that does not correspond to the limit values of the

emitted interference of class B (residential area and small enterprises.
When using the product in residential areas or small enterprises, the operator has to take

actions to prevent radio interferences (also refer to DIN EN 55022).

Technical data

7.1

General technical data

Table 5: Technical data

Weight

0.120 kg

Degree of protection

IP 20 acc. to DIN EN 60 529

7.2

Voltage supply and current consumption

The following specifications include the values acc. to EN 61131-2.

Infeed U

24 V DC PELV/SELV (safety extra-low voltage)

Maximum voltage range allowed

18 V DC to 31.2 V DC (incl. all tolerances and

ripple)

Current consumption from

0.2 A max.

Power consumption from

4.8 W max.

Reverse voltage protection of the supply voltage

Diode

Fuse protection

Internal protective fuse, 4 A

Transient protection

Present, suppressor diodes

Voltage dips at current supply interfaces

Up to 10 ms without impairment

Tec

hnical dat

Содержание Rexroth IndraControl XFE 01.1 Series





































Результаты поиска

Содержание Rexroth IndraControl XFE 01.1 Series

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE 01.1 Series

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl XFE 01.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth IndraControl XFE 01.1 Series

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE 01.1 Series

Бренды по названию

Популярные бренды