Bosch Rexroth IndraControl VCP 08.2 Скачать руководство пользователя

Страница: 48 / 78

-10

Bosch Rexroth AG

| Electric Drives and Controls

Rexroth IndraControl VCP 08

R911310379

Interfaces

1. Female Connector X5 (Ethernet)

2. Female Connectors X9, X10 (USB Host - Type A)

3. Female Connector X6 (DeviceNet)

4. Threaded Bolt for Protective Grounding

5. Connector X1 (Supply Voltage)

6. Diagnostics LED (DeviceNet)

7.3.1.1

Pin Assignment

Fig. 7-16:

5 pin connector

Connector in the small operating terminal: 5 pin male connector strip.

7.3.1.2

Cable

The maximum length allowed for spur lines connected to the bus cable
is 6 meters. The overall length of the bus cable including all spur lines
is not to exceed the maximum length listed in the table below.

Pin

Designation

Function

Not Connected

CAN_L

CAN_L Bus Line (Dominant LOW)

Drain

Shield

CAN_H

CAN_H Bus Line (Dominant HIGH)

Not Connected

Fig. 7-17:

Pin assignment of DeviceNet interface

For the connection, use a 5 pin connector with gold-plated contacts and
cover cap.

A DeviceNet-certified cable must be used.

Cable
type

Loop resistance

Surge
impedance

Capacitance per
unit length

2 x 1.1 mm < 22.6 Ohm/km

120 Ohm

< 39.4 pf/m

2 x 0.6 mm < 91.8 Ohm/km

120 Ohm

< 39.4 pf/m

Fig. 7-18:

Data line DeviceNet

Содержание Rexroth IndraControl VCP 08.2















































































Результаты поиска

Содержание Rexroth IndraControl VCP 08.2

Отзывы:

Похожие инструкции для Rexroth IndraControl VCP 08.2

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl VCP 08.2, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraControl VCP 08.2

Отзывы:

Похожие инструкции для Rexroth IndraControl VCP 08.2

Бренды по названию

Популярные бренды