Bosch Rexroth IndraControl VCP 08.2 Скачать руководство пользователя | Manualshive

Страница: 11 / 78

background image

R911310379

/

02

|

Rexroth IndraControl VCP 08

Electric Drives and Controls |

Bosch Rexroth AG

3

-1

Safety Instructions for Electric Drives and Controls

3

Safety Instructions for Electric Drives and Controls

3.1

Introduction

Read these instructions before the initial startup of the equipment in
order to eliminate the risk of bodily harm or material damage. Follow
these safety instructions at all times.Do not attempt to install or start up
this equipment without first reading all documentation provided with the
product. Read and understand these safety instructions and all user
documentation of the equipment prior to working with the equipment at
any time. If you do not have the user documentation for your equip-
ment, contact your local Bosch Rexroth representative to send this
documentation immediately to the person or persons responsible for
the safe operation of this equipment. If the equipment is resold, rented
or transferred or passed on to others, then these safety instructions
must be delivered with the equipment.

3.2

Explanations

The safety instructions describe the following degrees of hazard seri-
ousness in compliance with ANSI Z535. The degree of hazard serious-
ness informs about the consequences resulting from non-compliance
with the safety instructions.

WARNING
Improper use of this equipment, failure to follow the safety instruc-
tions in this document or tampering with the product, including
disabling of safety devices, may result in material damage, bodily
harm, electric shock or even death!

Warning
symbol

Signal word and degree of hazard seriousness
according to ANSI

DANGER

Death or severe bodily harm will occur.

WARNING

Death or severe bodily harm may occur.

CAUTION

Bodily harm or material damage may occur.

Fig. 3-1:

Hazard classification (according to ANSI Z535)

«
...
9
10
11
12
13
...
»

Содержание Rexroth IndraControl VCP 08.2















































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraControl VCP 08.2

Бренд: VeriFone Страницы: 2

Бренд: Sharp Страницы: 2

Бренд: Sharp Страницы: 34

Бренд: Sharp Страницы: 59

Бренд: Sharp Страницы: 344

Бренд: Sharp Страницы: 123

Бренд: Sharp Страницы: 132

Бренд: Sharp Страницы: 146

Бренд: CPI Страницы: 10

Бренд: quadient Страницы: 4

Бренд: Xircom Страницы: 54

Бренд: Ingenico group Страницы: 24

Бренд: OEZ Страницы: 4

Бренд: Ingenico group Страницы: 9

Бренд: 3nStar Страницы: 12

Бренд: ICP Страницы: 31

Бренд: iDiPOS Страницы: 51

Бренд: NCR Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды