manualshive.com logo in svg

Bosch Rexroth IndraControl S20, Руководство пользователя

Поделиться
Скачать
Bosch Rexroth IndraControl S20 Скачать руководство пользователя страница 74

14.3 

Mounting and electrical installation

Checklist for mounting and the electric installation of the module

Device type, equipment ID

 

Version: HW/FW

 

Date

 

Editor

 

Tester

 

Notes

 

No. Request (mandatory)

Yes

Notes

1

Was the mounting performed acc. to the spec‐

ifications (specifications from the planning

phase or acc. to the user manual)?

□

 

2

Was the module installed and fastened cor‐

rectly in the control cabinet PC (IP54)?

□

 

3

Do the cross sections and the cable wiring

correspond to the specifications?

□

 

4

Does the connection technique correspond to

the specifications made in the technical data

in the corresponding user manual?

□

 

No. Request (optional)

Yes

No

Notes

5

Is the protocol or the address set correctly ac‐

cording to the specification?

□

□

 

 

Date

Signature (edi‐

tor)

Date

Signature (test‐

er)

Bosch Rexroth AG

 DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

72/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Checklists

Содержание Rexroth IndraControl S20

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды