Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 69 / 88

13.3

Device parameters (safe parameterization)

The device parameters are individual module parameters within the safe pa‐

rameterization, refer to

chapter 6.2 "Parameterizing the safe outputs" on

page 29

SCCRC

The device parameters are crosschecked with a checksum, the Safety Con‐

figuration CRC (SCCRC).

13.4

CSos diagnostic messages

Error code

Error cause

Description

Solution

Dec

Hex

6144

0x1800

Configuration is owned

by another originator

The module was configured by an‐

other originator

Change SNN or SDID using DIP

switches. The safe originator ID is

deleted upon a new voltage start‐

up.

6145

0x1801

Output is owned by an‐

other originator

The module was configured by an‐

other originator

Change SNN or SDID using DIP

switches. The safe originator ID is

deleted upon a new voltage start‐

up.

6147

0x1803

Electronic Key mis‐

match: Product Code

or Vendor ID

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6148

0x1804

Electronic Key mis‐

match: Device Type

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6149

0x1805

Electronic Key mis‐

match: Revision

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6150

0x1806

Output Connection

Point not found

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6151

0x1807

App.Path: Configura‐

tion Class invalid

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6152

0x1808

App.Path: Configura‐

tion Assembly Instance

invalid

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6153

0x1809

App.Path: Config. As‐

sembly Instance does

not exist

The configured device (SDDML

file) does not match the physically

installed module

Request new SDDML file or install

the correct module

6154

0x180A

SCCRC mismatch in

Type1 SafetyOpen

The SCCRC entered into the user

interface under "Safe Configura‐

tion" does not match the SCCRC

calculated in the "Safe Parameter‐

ization"

Copy SCCRC from the "Safe Pa‐

rameterization" to the "Safe Con‐

figuration"

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

67/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

CSos parameters and device parameters

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды