Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 65 / 88

CSos glossary

CIP Safety (Common Industrial

Protocol Safety)

This safe protocol is used for the safe data transfer in the Sercos bus.

CRC

Cyclic Redundancy Check = CRC check value
The validity of the process data in the safety telegram is checked using a

CRC check value. The assigned address books are checked and the safety-

relevant parameters are also backed up. This value is part of the safety tele‐

gram.

CSos

"CSos" is the abbreviation for "CIP safety on sercos", which is the safe chan‐

nel in Sercos.

Consumer

Device receiving safe data

Diagnostic coverage (DC)

The effectiveness of the diagnostics is determined as ratio between the fail‐

ure rate of the identified hazardous failures and the total failure rate of all

hazardous failures.
Note 1: The diagnostic coverage can either apply to the complete system or

to components of the safety-related systems. A diagnostics coverage could

for example be available for sensors and/or the logic system and/or correct‐

ing elements.
Note 2: Following IEC 61508-4:2010, term 3.8.6.

Dynamization

The dynamization is intended to identify error states in the safety-relevant cir‐

cuitries. It is automatically dynamized in the background without affecting the

safety function or the default drive functions.

Expected Packet Interval (EPI)

Generation rate of cyclic messages.

Errors

State of a unit characterized by the inability to perform a requested function,

excluding the inability during preventive maintenance or other planned ac‐

tions or due to lack of external resources (IEC 60050-191:1990, 05-01).
Note 1: An error is often caused when the unit itself fails, but it can also be

present without previous failure.
Note 2: In this part of the ISO 13849, "Error" means accidental error.

FMEA (Failure Mode and Effects

Analysis)

FMEA is an analytic method of the preventive quality assurance. It is used to

find potential vulnerabilities and to detect their relevance and evaluate them

and to introduce measures for their avoidance or detection on time. The sys‐

tematic analysis and recovery of vulnerabilities minimizes the risk, reduces

the error costs and improves the reliability.

Format type

CIP telegram format (base format, extended format).

Functional safety

Part of the overall safety relating to the EUC and EUC control system which

depends on the correct functioning of the safety-related system E/E/PE sys‐

tem and other risk reducing measures (IEC 61508-4:2010, 3.1.12).
EUC: Installation, machine, apparatus or system used for manufacturing, ma‐

terial deformation, transportation, medical or other activities (IEC

61508-4:2010, 3.2.1).
EUC control system: System responding to the input signals of the process

and/or an operator and generating output signals allowing the EUC to work

as intended (IEC 61508-4:2010, 3.3.3).

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды