manualshive.com logo in svg

Bosch Rexroth IndraControl S20, Руководство пользователя

Поделиться
Скачать
Bosch Rexroth IndraControl S20 Скачать руководство пользователя страница 59

11.2.4 

Safety characteristics acc. to EN 62061

Attainable SIL claim limit

SILCL = SIL 2 (single-channel)
SILCL = SIL 3 (dual-channel)
Depending on the parameterization and wiring, re‐

fer to 

chapter 3.6  "Connecting options for actua‐

tors depending on the parameterization" on page

14

 and refer to 

chapter 7  "Connection examples

of the safe outputs" on page 33

Safe Failure Fraction (SFF)

99 %

Probability of dangerous failure

per hour for the complete mod‐

ule (PFH)

SIL 2: Up to 1 % of 10

-6

 (corresponds to 1 * 10

-8

 )

SIL 3: Up to 1 % of 10

-7

 (corresponds to 1 * 10

-9

Depending on the parameterization, refer to

"SIL/SIL CL" on page 35

Hardware error tolerance (HFT)

of the module

1

Permitted service life

20 years, at a low demand rate 25 years.

Tab. 11-5:

Safety characteristics acc. to EN 62061

11.2.5 

Safety characteristics acc. to EN ISO 13849-1

Attainable performance level

PL d (single-channel)
PL e (dual-channel)
Depending on the parameterization and wiring, re‐

fer to 

chapter 3.6  "Connecting options for actua‐

tors depending on the parameterization" on page

14

 and refer to 

chapter 7  "Connection examples

of the safe outputs" on page 33

Diagnostic coverage (DC)

99 %

Mean time up to a dangerous

failure (MTTFd)

100 years

Tab. 11-6:

Safety characteristics acc. to EN ISO 13849-1

11.2.6 

Supply voltage U

BUS

 (logic)

Logic voltage

5 V DC

Current consumption from U

BUS

Typ. 260 mA (all outputs set, supplied by U

O

 from

19.2 V DC to 30.2 V DC)
280 mA max.

Tab. 11-7:

Supply voltage U

BUS

 (logic)

The bus coupler or infeed terminal of the station supply the mod‐

ule with the logic voltage U

BUS

.

For the technical data, refer to the data sheet of the bus coupler

or the infeed terminal.

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P 

Bosch Rexroth AG

57/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Technical data and ordering data

Содержание Rexroth IndraControl S20

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды