Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 50 / 88

Unintended machine startup due to start or

restart after adding voltages as well as the

missing request of the safety function

WARNING

●

Observe the following notes:
–

The module starts after the successful download of the configura‐

tion and parameter data set as well as after the successful pro‐

cessing of the internal check.

–

A safety-relevant input is automatically set again to "1" if the trigger

of the safety function is reset.

●

If an automatic restart is not intended, make the corresponding settings

in the safety logic.

9.2.2

Errors of the safe digital outputs

Code

Error cause

LED

Description, effect

Acknowledgement, remedy

0x2370 Cross fault between

two outputs

All

OUT

red on

A cross-fault to another output or to an

external voltage was determined. All out‐

puts are thus retained in the safe state.

Read out channel number via the

DiagStateChannelNo object 0x033.
Check actuators, plugs and cabling.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.
If the error remains pending, the

message is output again.

0x2371 Cross-fault between

external voltage and

one output

0x2344 Short-circuit or over‐

load at the displayed

output

OUT

red on

Short-circuit or overload was detected at

the displayed output. The respective out‐

put is thus retained in the safe state.

Read out channel number via the

DiagStateChannelNo object 0x033.
Check actuators, plugs, cabling and

the free-wheeling circuit at the con‐

tactor.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.
After a successful acknowledge‐

ment, the safe module additionally

expects a positive edge of the ap‐

plication for the added output. For

the dual-channel parameterization,

this also applies to the other possi‐

bly error-free output.

0x8F08 Light test error at the

displayed output

All

OUT

red on

Due to the test pulses (short-term switch-

on), an error was detected at the dis‐

played output. All outputs are thus re‐

tained in the safe state. A possible cause

can be the short-circuit event in the exter‐

nal wiring during the test.

Read out channel number via the

DiagStateChannelNo object 0x033.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

48/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Errors: Reporting and troubleshooting

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды