Bosch Rexroth IndraControl S20 страница 13 Скачать руководство пользователя

Страница: 13 / 88

Product description

3.1

Brief module description

The module S20-SSDO-8/3 is a safe output module to be used in an

IndraControl S20 station at any position in a Sercos I/O system. The module

can only be used together with a safety control. The safe connection is estab‐

lished via the safe bus protocol CSos (CIP Safety on Sercos).
Set the TUNID (SNN and SDID) for the Csos device via a DIP switch.
The module is provided with four safe digital outputs for the dual-channel as‐

signment or eight digital outputs for the single-channel assignment.
The outputs can be parameterized user-specifically and allow the integration

of actuators into the safe Csos system.
In the Csos system, safety categories with the following requirements can be

met with the module depending on the application conditions:
●

Up to SIL 3 acc. to IEC 61508

●

Up to SILCL 3 acc. to EN 62061

●

Up to cat. 4/PL e acc. to EN ISO 13849-1

3.2

Module structure

Bus base module

Electronics module

Plug to connect the supply voltage

Color code of the function

Peripheral connector

Diagnostic and status displays

DIP switch

Fig. 3-1:

Module structure

For more information on the settings of the DIP switches, refer to

chapter 5.1.3 "Setting DIP switch" on page 23

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

11/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Product description

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды