Bosch Rexroth HMU05.1N Series Скачать руководство пользователя

Страница: 133 / 410

View

Identifica‐

tion

Function

L+

L-

Connections for screwing on DC bus bars
Threads on connecting bolt: 2 x M10
Tightening torque: 48 Nm

Unit

Dimensions

See component dimensional drawing

Short circuit protection

Upstream fuse elements in mains connection

Overload protection

Upstream fuse elements in mains connection

Tab. 6-10:

Function, pin assignment, properties

Notes on installation

Select the connection cross section according to the maximum current load

occurring on the DC bus and the installation method for the connections.

Risk of damage by reversing the polarity of

the DC bus connections L- and L+

NOTICE

Make sure the polarity is correct.

Shield connection

Control line shield connection

Shield connection for control lines of the control section, motor, etc. whose

connectors do not have a shield connection.

Always connect the shields with the largest possible metal-to-met‐

al contact surface.

Fig. 6-2:

Shield connection of shielded control lines

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

131/407

Rexroth IndraDrive ML Drive Systems with HMU05

Mounting and installation

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды