Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 112

Страница: 112 / 410

Risk of fire caused by missing fuses!

NOTICE

Install fuses. In case a short circuit occurs in the drive controller, a fuse pro‐

vides optimum safety against overheating or fire (see also IEC 61800‑5‑1 and

UL 508C).
For distribution in North America, single fuses are required for this type of

mains connection (see UL 508A).
In the scope of international and European standards (IEC/EN, not North

America), it is allowed to use a group fuse instead of the single fuses. When

selecting the nominal current of the group fuse, observe the loop impedance,

the line length and the line cross section of the mains supply feeder (see IEC

60204-1, chapter Appendix A).
Observe the data for dimensioning line cross sections and fuses (see also

IEC 60204‑1, UL 508A and NFPA 79).

Mains connected load and mains current

Technical data of the components

●

See

chapter 7.2.2 "Mains voltage" on page 139

●

See

chapter 7.2.3 "DC bus" on page 141

Calculating the mains-side phase current

The mains-side phase current is required for the following cases:
●

Selecting mains contactor

●

Determining fuses in the mains connection

●

Determining line cross section

●

Selecting other components in the mains connection (mains filter, mains

choke)

Operation under rated conditions

For data on mains contactor, fuses and cross section in operation under rat‐

ed conditions, see technical data of the respective component.

Operation at partial load

Operation at partial load can lead to smaller mains contactors, fuses and line

cross sections.
If defined data for operation at partial load are available, the mains-side

phase current can be determined as follows:
1.

Determine motor power
Take power of drive controller-motor combination from Rexroth Indra‐

Size or calculate it.

mHa

Mechanical nominal power for main drives (shaft

output) [kW]

Nominal motor torque [Nm]

Nominal motor speed [min

-1

]

Determine DC bus power from motor power and efficiency

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

110/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды