manualshive.com logo in svg

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Поделиться
Скачать
Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 106

ed  direct  fault  currents  that  can  be  produced  in  power  supply  units,

mains rectifiers and drive controllers with power converters in B6 circuit,

the residual-current-operated circuit breaker is not triggered. This blocks

the triggering of a residual-current-operated circuit breaker sensitive to

power  pulse  current  in  the  case  of  ground  contact,  i.e.  in  the  case  of

error.
Residual-current-operated circuit breakers sensitive to power pulse cur‐

rent do not provide any protection against inadmissible contact voltage.

2.

Residual-current-operated circuit breakers sensitive to universal current

(type B acc. to IEC 60755)
These circuit breakers are suited for smoothed direct fault currents, too,

and safely switch off devices with B6 input rectifiers.
If  a  current  with  30  mA  triggers  the  residual-current-operated  circuit

breaker, it is possible to use a residual-current-operated circuit breaker

with a higher tripping current for machine protection.
If this residual-current-operated circuit breaker triggers accidentally, too,

check  in  how  far  the  above  conditions  and  dependencies  can  be  im‐

proved (for example, by connecting current-compensated mains chokes

in the incoming circuit, increasing the inrush current limitation).

Using isolating transformer to re‐

duce leakage current in mains

If there is no improvement achieved and the residual-current-operated circuit

breaker, due to specific mains conditions on site, has to be used neverthe‐

less on the mains input side, connect an isolating transformer between mains

connection and power connection of the drive system. This reduces the leak‐

age current in the ground wire of the mains that is produced during normal

operation  which  allows  the  residual-current-operated  circuit  breaker  to  be

used.  Connect  the  neutral  point  of  the  secondary  winding  of  the  isolating

transformer to the equipment grounding conductor of the drive system.
Adjust the ground-fault loop impedance to the overcurrent protective device

so that the unit can be switched off in the case of failure.
Before operating enable, check the correct function of the overcurrent protec‐

tion device including activation in the case of failure.
Exclusive fusing by residual-current-operated circuit breaker
For  drive  systems  with  electronic  drive  controllers,  exclusive  protection  by

means of a residual-current-operated circuit breaker normally is not possible

and not allowed.
Electronic equipment that has a nominal power higher than 4 kVA or is des‐

tined for permanent connection does not need residual-current-operated cir‐

cuit breakers.
According  to  IEC  60204‑1  and  IEC  61800‑5‑1,  the  mains-side  protection

against indirect contact, i.e. in the case of insulation failure, has to be provi‐

ded in a different way, for example by means of an overcurrent protection de‐

vice, protective grounding, protective-conductor system, protective separation

or total insulation.

Mains types

TN-S mains type

The TN-S mains type is the usual mains type in Europe.

Bosch Rexroth AG

 DOK-INDRV*-HXX05******-PR02-EN-P

104/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды