Bosch Rexroth GTE Series Скачать руководство пользователя

Страница: 11 / 88

Important Instructions on Use

2.1

Intended Use

2.1.1

General Information

Introduction

Rexroth products are developed and manufactured according to the state of

the art. Before they are delivered, they are inspected to ensure that they operate

safely.
The products must only be used as intended. If they are inappropriate used,

situations may arise resulting in injuries to property and persons.

Rexroth, as the manufacturer, does not provide any warranty, as‐

sume any liability, or pay any damages for damage caused by

products not being used as intended. Any risks resulting from the

products not being used as intended are the sole responsibility of

the user.

Before using the Bosch Rexroth products, the following condition precedent

must be fulfilled so as to ensure that they are used as intended:
●

Everyone who in any way whatsoever handles one of our products must

read and understand the corresponding notes regarding safety and re‐

garding the intended use.

●

If the products are hardware, they must be kept in their original state, i.e.

no constructional modifications must be made. Software products must

not be decompiled; their source codes must not be modified.

●

Damaged or improperly working products must not be installed or put into

operation.

●

It must be ensured that the products are installed according to the regu‐

lations specified in the documentation.

2.1.2

Areas of Use and Application

Typical application ranges of the GTE planetary gearboxes are:
●

Handling and Mounting systems,

●

Packaging and Food-processing machines,

●

Printing and Paper-processing machines and

Controlling and monitoring of the motor/-gearbox combination may require con‐

nection of additional sensors and actuators.

The gearboxes may only be used with the accessories specified in

the documentation. Components that are not explicitly mentioned

must neither be attached nor connected. The same is true for cables

and lines.

The operation must only be carried out in the explicitly mentioned

configurations and combinations of the component and with the

software and firmware specified in the corresponding functional de‐

scription.

Any drive controller must be programmed before startup, in order to ensure that

the motor executes the functions specific to the particular application.

DOK-GEAR**-GTE********-PR06-EN-P
Rexroth GTE Planetary Gearboxes

Bosch Rexroth AG

9/85

Important Instructions on Use

LSA Control S.L. www.lsa-control.com [email protected] (+34) 960 62 43 01

Содержание Rexroth GTE Series

























































































Результаты поиска

Содержание Rexroth GTE Series

Отзывы:

Похожие инструкции для Rexroth GTE Series

Бренды по названию

Популярные бренды

Bosch Rexroth GTE Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth GTE Series

Отзывы:

Похожие инструкции для Rexroth GTE Series

Бренды по названию

Популярные бренды