Bosch rexroth CytroForce-M Скачать руководство пользователя страница 61

Страница: 61 / 85

61 / 85

Servo-hydraulic actuator

Cleaning and care

Bosch Rexroth AG

RE62270-B, 01.21

Maintenance and repair

10.1

General

WARNING

Dangerous voltages and risk of electric shock! In order to

avoid injuries when working on electrical systems you

should take the following precautions in the order listed:

−

Disconnect completely

−

Secure against re-connection. Observe the discharge

time of the converters!

−

Verify that the installation is dead

−

Carry out earthing and short-circuiting

−

Cover or shield against adjacent live parts

WARNING

Danger due to pressurized servo-hydraulic actuator! Risk

of injury! Severe injury when working on systems that

have not been shut down! Damage to property! Even

after the servo-hydraulic actuator was disconnected from

the electrical power supply, the system is still under

pressure and is permanently prestressed!

−

Observe the specifications of the system manufac-

turer and the system end-user.

−

Do not disconnect line connections, ports or compo-

nents as long as the servo-hydraulic actuator is pres-

surized.

−

The hydraulic circuit may only be opened by specifi-

cally trained personnel.

WARNING

Systems that are still running! Risk of injury! The work

steps described in this chapter may only be performed

on shut down systems. Before beginning work:

−

Make sure that the drive motor cannot be switched

on.

−

Ensure that all force-transmitting components and

connections are (electrically) switched off and

secured against restarting according to the manufac-

turer's instructions. If possible, remove the main fuse

of the system. Verify with the help of inspected meas-

uring equipment that there is no voltage applied.

10.2

Cleaning and care

NOTICE

Solvents and aggressive cleaning agents! Aggressive

cleaning agents can damage the seals of the drive unit

and make them age faster.

−

Never use solvents or aggressive cleaning agents.

NOTICE

Ingress of dirt and liquids! This will result in the fact that

safe operation of the servo-hydraulic actuator can no

longer be ensured.

−

When carrying out any work, observe strictest cleanli-

ness.

−

Do not use a high-pressure washers or hose water.

For cleaning and care, please observe the following:

●

Plug all openings with suitable protective caps/devices.

●

Check that all seals and plugs of the plug-in connections are tightly seated

to ensure that no moisture can enter the drive unit during cleaning.

Содержание rexroth CytroForce-M






















































































Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды

Bosch rexroth CytroForce-M, Руководство по эксплуатации

Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды