Bosch rexroth CytroForce-M Скачать руководство пользователя страница 41

Страница: 41 / 85

41 / 85

Servo-hydraulic actuator

Mounting the servo-hydraulic actuator

Bosch Rexroth AG

RE62270-B, 01.21

7.5.4

Electrical installation

General

WARNING

High electrical voltage! Touching parts with voltages

greater than 50 V can be dangerous to people and lead

to electric shock. When the servo-hydraulic actuator and

the drive controller are operated, certain parts are inevi-

tably under voltage.

−

Mounting, operation and maintenance and/or repairs

of components of the servo-hydraulic actuator and

the drive controller may exclusively be carried out by

Bosch Rexroth or by authorized and qualified per-

sonnel of a specialized company that was authorized

by Bosch Rexroth, see

⮫

Chapter 2.4 “Qualification of

personnel” on page 12.

−

Please observe the general installation and safety reg-

ulations when working on high-voltage systems.

−

Before switching on, the equipment grounding con-

ductor must have been permanently connected to all

electric components in accordance with the connec-

tion diagram.

−

Never operate electrical equipment, even for short-

time measurements or tests, if the protective earthing

conductor is not permanently connected to the points

of the components provided for this purpose.

−

Disconnect the electrical components from the mains

or from the voltage source before accessing parts

with voltages exceeding 50 V. Secure electrical com-

ponents against restarting.

−

After switching off, you should generally wait for 30

minutes before you touch an electrical component in

order to allow the live capacitors in the drive control-

lers to discharge. Measure the electrical voltage of

live parts before beginning work in order to avoid haz-

ards caused by contact.

−

Before switching on, attach the covers and protective

devices provided for contact protection.

−

Do not touch the electrical connection points of the

components when the system is activated.

−

Do not disconnect or connect the connectors under

voltage.

WARNING

High housing voltage and high working current! Due to

the high housing voltage and the high working current,

touching can lead to electric shocks and severe injuries.

−

Connect the equipment grounding conductor of the

components of the electric drive and control system

permanently to the main power supply at all times.

The leakage current is greater than 3.5 mA.

−

Observe the minimum cross-section of the protective

earthing connection.

Содержание rexroth CytroForce-M






















































































Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды

Bosch rexroth CytroForce-M, Руководство по эксплуатации

Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды