Bosch Rexroth A10VG Скачать руководство пользователя | Manualshive

Страница: 45 / 64

background image

Installation 45/64

RE 92750-01-B/06.2018, A10VG, Series 10,

Bosch Rexroth AG

7.4.11 Electrically connecting the axial piston unit

NOTICE

Short circuit due to penetrating hydraulic fluid!
Fluid can penetrate the product and cause a short circuit!

▶

Do not install axial piston units with electric components (e.g. electric controls,
sensors) in a reservoir below the fluid level (inside-reservoir installation).

The machine/system manufacturer is responsible for the layout of the electric
control.
Electrically controlled axial piston units must be connected in accordance with the
electrical circuit diagram for the machine/system.
For axial piston units with electrical control and/or mounted sensors, observe the
information in data sheet 92750, e.g.:

• Permissible voltage range

• Permissible current

• Correct pin assignment

• Recommended electrical control units

Exact details on the connector, type of protection and matching mating connector
can also be found in data sheet 92750. The mating connector is not included in the
scope of delivery.

1.

Switch off the power supply to the relevant system component.

2.

Electrically connect the axial piston unit (12 or 24 V). Before connecting, check
whether the connector protective covers (3) are off (see Fig. 11 “Removing
transport protection” on page 38), and the connector and all seals are intact.

If necessary, you can change the position of the connector by turning the solenoid
body. This is not dependent on the connector version.

CAUTIOn! Hot surfaces on the solenoid!
Risk of burns!

▶

Allow the solenoid to cool down sufficiently before touching it.

▶

Wear heat-resistant, protective clothing, e.g., gloves.

To do this, proceed as follows:

1.

Loosen the mounting nut (1) of the solenoid. To do this, turn the mounting
nut (1) one turn counter-clockwise.

2.

Turn the solenoid body (2) to the desired position.

3.

Re-tighten the mounting nut. Tightening torque of the mounting nut: 5+1 Nm.

Changing connector

position

1

2

«
...
43
44
45
46
47
...
»

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth A10VG

Бренд: Nelson Страницы: 12

Бренд: Zilmet Страницы: 10

DOMINATOR Series

Бренд: RBI Страницы: 52

Бренд: TATRA Страницы: 16

FUTERA II Series

Бренд: RBI Страницы: 32

Бренд: WarmPool Страницы: 26

Бренд: WAGNER Страницы: 100

flexoTHERM exclusive VWF 57/4

Бренд: Vaillant Страницы: 20

AquaMax Eco Expert

Бренд: Oase Страницы: 60

Бренд: Xylem Страницы: 92

LOWARA e-SV Series

Бренд: Xylem Страницы: 48

MPXI11MULTIPC18

Бренд: Master Pumps Страницы: 32

Бренд: Masterflex Страницы: 67

Taro HCS SJ Series

Бренд: Texmo Industries Страницы: 41

Бренд: KISANKRAFT Страницы: 44

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

SMOOTHFLO Series

Бренд: Remco Страницы: 2

Бренд: vacuubrand Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды