Bosch Rexroth A10VG Скачать руководство пользователя | Manualshive

Страница: 36 / 64

background image

36/64 Installation

Bosch Rexroth AG

, Series 10 A10VG, RE 92750-01-B/06.2018

7.4.4 Installation with a coupling
The following describes how to install the axial piston unit with a coupling:

nOTICE! Danger from improper handling!
Product can be damaged!

▶

Do not install the coupling hub on the drive shaft of the axial piston unit by
striking it.

1.

Install the specified coupling half on the drive shaft of the axial piston unit
according to the instructions of the coupling manufacturer.

The drive shaft of the axial piston unit is equipped with a female thread. Use this
female thread to pull the coupling element onto the drive shaft. The size of the
female thread can be seen in the installation drawing.

2.

Clamp the coupling hub onto the drive shaft or ensure permanent lubrication
of the drive shaft. This prevents the formation of frictional corrosion and the
associated wear.

3.

Transport the axial piston unit to the installation location.

4.

Remove dirt and foreign particles from the installation location.

5.

Install the coupling on the output shaft of the drive motor in accordance with the
specifications provided by the coupling manufacturer.

Do not fasten down the axial piston unit until the coupling has been correctly
installed.

6.

Fasten the axial piston unit at the installation location.

7.

Align the drive shaft of the axial piston unit and the output shaft of the drive
motor so there is no angular deviation.

8.

Make sure no excessive axial and radial forces are acting on the drive shaft.

9.

For bell housing installation, check the coupling axial play through the bell
window according to the manufacturer's specifications.

10.

Details on the required tools and tightening torques for the mounting bolts are
available from the machine/system manufacturer.

11.

When using elastic couplings, check that the drive does not resonate after
completing the installation.

7.4.5 Installation on a gearbox
The following describes how to install the axial piston unit on a gearbox.
After installing on a gearbox, the axial piston unit is covered and is difficult to access:

▶

Before installing, make sure that the spigot diameter centers the axial piston unit
(observe tolerances) and that no excessive axial or radial forces are acting on the
drive shaft of the axial piston unit (installation length).

▶

Protect the drive shaft against frictional corrosion by providing permanent
lubrication.

▶

Fasten the axial piston unit at the installation location.

«
...
34
35
36
37
38
...
»

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth A10VG

Бренд: TapFlo Страницы: 35

Бренд: Panasonic Страницы: 224

Бренд: vacuubrand Страницы: 76

45 E Frame Series

Бренд: Danfoss Страницы: 44

ElectriFLEX LD LE Series

Бренд: Bradford White Страницы: 40

Бренд: Powerhorse Страницы: 48

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

Бренд: Honda Страницы: 25

WS G140DC6 Series

Бренд: Waterstage Страницы: 64

Бренд: IBC Страницы: 8

Бренд: Raypak Страницы: 40

SkyAir RZR-P Series

Бренд: Daikin Страницы: 202

Бренд: Calorex Страницы: 28

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Бренд: SUN HoM Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды