Bosch Rexroth A10VG Скачать руководство пользователя | Manualshive

Страница: 12 / 64

background image

12/64

Safety instructions

Bosch Rexroth AG

, Series 10 A10VG, RE 92750-01-B/06.2018

2.6 Product-specific safety instructions

The following safety instructions apply to chapters 6 t o 14.

wARnInG

Danger from excessive pressure!
Risk of death or injury, or property damage!
Improperly changing the factory pressure settings can result in a pressure increase
beyond the max. permissible pressure.
Operating the unit above the max. permissible pressure can cause components to
burst and hydraulic fluid to escape under high pressure.

▶

Changes to the factory settings should only be made by Bosch Rexroth
specialists.

▶

In addition, a pressure relief valve is required in the hydraulic system as a back-
up. If the axial piston unit is equipped with a pressure cut-off and/or pressure
controller, this is not an adequate safeguard against pressure overload.

Danger from suspended loads!
Risk of death or injury, or property damage!
Improper transportation may cause the axial piston unit to fall down and lead to
injury, e.g., crushing or fracture, or damage to the product.

▶

Make sure that the load bearing capacity of the lifting device is sufficient to
safely bear the weight of the axial piston unit.

▶

Never stand or put your hands under a suspended load.

▶

Make sure the unit remains stable during transport.

▶

Wear your personal protective equipment (e.g., safety goggles, safety gloves,
suitable working clothes, safety shoes).

▶

Use suitable lifting devices for transportation.

▶

Observe the prescribed position of the lifting strap.

▶

Observe the national laws and regulations on occupational health and safety,
and transportation.

System/machine under pressure!
Risk of death or serious injury when working on unsecured machines/systems! Risk
of property damage!

▶

Switch off the entire system and secure it against reactivation according to the
parameters provided by the machine/system manufacturer.

▶

Make sure all relevant components in the hydraulic system are depressurized.
Follow the machine/system manufacturer's specifications.

▶

Note that the hydraulic system may still may be under pressure even after the
pressure supply itself has been disconnected.

▶

Do not disconnect any line connections, ports or components as long as the
hydraulic system is under pressure.

«
...
10
11
12
13
14
...
»

Содержание Rexroth A10VG

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth A10VG

Бренд: York International Страницы: 87

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Бренд: Panasonic Страницы: 20

PacificHydrostar 2" Gasoline Powered Clear Water...

Бренд: Pacific hydrostar Страницы: 24

Бренд: Cordivari Страницы: 44

Бренд: Tiger Страницы: 36

Бренд: Masterflex Страницы: 67

Бренд: Endress Страницы: 17

Бренд: EBARA Страницы: 69

Altherma 3 R MT F+W

Бренд: Daikin Страницы: 68

Бренд: DAB Страницы: 25

Бренд: Bard Страницы: 27

FIGHTER 2010 Series

Бренд: Nibe Страницы: 36

Бренд: Q-Pumps Страницы: 44

Бренд: Oase Страницы: 42

Zoneline AZ91H18E E Series

Бренд: GE Страницы: 78

Little Giant 16 G Series

Бренд: Franklin Electric Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды