Bosch Rexroth 11 Series Скачать руководство пользователя | Manualshive

Страница: 26 / 60

background image

26/60 Installation

Bosch Rexroth AG

, A15VSO/A15VLO Series 11, RE 92801-01-B/11.2018

7 Installation

Prior to installation, the following documents should be to hand:

• Installation drawing for the axial piston unit (can be obtained from your contact

person at Bosch Rexroth)

• Hydraulic circuit diagram for the axial piston unit (in the installation drawing)

• Hydraulic circuit diagram for the machine/system (available from the machine/

system manufacturer)

• Order confirmation (contains the order-related technical data for your axial

piston unit)

• Data sheet for the axial piston unit (contains the permissible technical data)

7.1 Unpacking

The axial piston unit comes in a polyethylene material (PE) corrosion protection film.

CAUTION!

Danger due to falling parts!

If the packaging is not opened correctly, parts may fall out and damage the parts
or even result in injury.

▶

Place the packaging on a level surface with sufficient load-bearing capacity.

▶

Only open the packaging from the top.

▶

Remove the packaging from the axial piston unit.

▶

Check the axial piston unit for transport damage and completeness; see chapter 4
"Scope of delivery" on page 17.

▶

Dispose of the packaging in accordance with the regulations in your country.

7.2 Installation conditions

The installation position and location of the axial piston unit essentially determine
how it is installed and commissioned (such as when filling and air bleeding the axial
piston unit).

▶

Install the axial piston unit so that the expected forces and torque can
be transferred without any danger. The machine/system manufacturer
is responsible for sizing the fasteners.

▶

Observe the permissible radial forces on the drive shaft when driving with radial
loading (belt drives). If necessary, store the belt pulley separately.

▶

Make sure the axial piston unit is always filled with hydraulic fluid during
commissioning and operation. Also do this also after relatively long standstill
periods, since the axial piston unit may drain out through the hydraulic lines.

▶

Direct the leakage in the housing area to the reservoir through the highest drain
port. Use a line size that matches the port.

▶

A check valve in the drain line is only permissible on a case-by-case
basis following consultation. Please consult your proper contact person
at Bosch Rexroth.

▶

To keep noise values low, use elastic elements to isolate all connecting lines from
all vibration-capable components (e.g. reservoir).

▶

Make sure the suction, drain, and return lines flow into the reservoir below the
minimum fluid level under all operating conditions. This will prevent air from
being drawn in and foam from forming.

«
...
24
25
26
27
28
...
»

Содержание Rexroth 11 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth 11 Series

Бренд: Water Worker Страницы: 24

TORNADO 2 Series

Бренд: Larius Страницы: 32

Бренд: SAER Elettropompe Страницы: 16

Бренд: vacuubrand Страницы: 76

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

Бренд: Campbell Страницы: 2

GPVX 75L Series

Бренд: A.O. Smith Страницы: 52

Бренд: Davey Страницы: 8

Бренд: Daikin Страницы: 44

Бренд: Raypak Страницы: 23

EWAA0 DAV3P Series

Бренд: Daikin Страницы: 240

Бренд: HERBORNER pumpentechnik Страницы: 39

Бренд: Santon Страницы: 12

Бренд: IWAKI PUMPS Страницы: 68

Бренд: Grundfos Страницы: 8

Hydromatic H3HX

Бренд: Pentair Страницы: 8

RSJ-100/N1-540V-D

Бренд: Midea Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды