Bosch MSK030B NSNN Series страница 27 Скачать руководство пользователя

Страница: 27 / 178

4.2

Conditions for Use of MSK Motors according to ATEX Classi‐

fication, Equipment Group II, Category 3.

Danger of explosion and life or high damage

to property!

DANGER

All used components and accessory parts must fulfill the requirements for ex‐

plosion protection according to the 2014/34/EU directive.
The conditions on use given in this documentation must be taken into ac‐

count for any project planning and be observed during operation.

Notes about test number

The Ex designation for MSK motors can be identified by the "X" at the end of

the type plate or declaration of conformity. Please observe the following spe‐

cial conditions for a safe operation of the motors in your construction:
●

The permissible ambient temperature range is 0 ... 40°C. Higher ambi‐

ent temperatures up to max. 55 °C are allowed at corresponding derat‐

ing

chapter 10.1.1 "Installation altitude and ambient temperature" on

page 115

●

Servicing and repairs are only permitted by the certified Rexroth service.

●

It is not allowed to exceed the specified values of the tensile loading via

cables which are connected via connectors. The maximum allowed val‐

ues are determined in the following context.

Z max

Tensile load of connection cable (maximum value)

Diameter cable outer jacket (maximum value)

Fig. 4-2:

Determination of maximum tensile load of connection cables

Danger of explosion due to exalted tensile

load of connection cables

WARNING

Adherence of specified limits.
Mechanical fastening of cable ends (e.g. use cable clamps after approx. 30

cm, ...).

The following maximum tensile load must be kept when using ready-made

cables.

Cable type ready-made RKL...

Raw cable INK... F

Z max

[N]

0014, 0019, 0053, 4302, 4303, 4305

0653 (1.0 mm²)

62.5

0015, 0016, 0017, 0045, 0050, 0054, 4300, 4301, 4304, 4306, 4307, 4320, 4325

0650 (1.5 mm²)

63.5

0018, 0051, 0052, 4308, 4309, 4310, 4312, 4321, 4326, 4343

0602 (2.5 mm²)

0056, 0058, 4313, 4314, 4315, 4316, 4322, 4327

0603 (4.0 mm²)

87.5

0049, 0055, 4317, 4318, 4319, 4323, 4328

0604 (6.0 mm²)

97.5

DOK-MOTOR*-MSK*EXGIIK3-PR09-EN-P

Bosch Rexroth AG

25/175

Synchronous Servomotors MSK For Potentially Explosive Areas

Explosion protection for MSK motors

Содержание MSK030B NSNN Series



















































































































































































Результаты поиска

Содержание MSK030B NSNN Series

Отзывы:

Похожие инструкции для MSK030B NSNN Series

Бренды по названию

Популярные бренды

Bosch MSK030B NSNN Series, Руководство по планированию проекта

Результаты поиска

Содержание MSK030B NSNN Series

Отзывы:

Похожие инструкции для MSK030B NSNN Series

Бренды по названию

Популярные бренды