Bosch HG 120B Series страница 8 Скачать руководство пользователя

Страница: 8 / 40

Installation and connection

4 Installation and connection

You can find out where and how best to install your ap-

pliance here. You will also learn how to connect your

appliance to the power supply.

4.1 Gas connection

Only an authorised expert or a licensed customer ser-

vice technician may install the appliance in accordance

with the instructions specified under "Gas connection

and conversion to a different gas type".

The settings for configuring your appliance can be

found on the rating plate on the rear of the appli-

ance. The gas type set at the factory is marked with

an asterisk (*).

Find out about the local supply conditions regarding

the gas type and gas pressure before installing the

appliance, and ensure that the gas setting for the

appliance complies with this information.

Connect and install this appliance in accordance

with the applicable to the installation instructions.

Do not connect this appliance to a waste gas main

on the combustion products. Do not connect this

appliance to an exhaust gas outlet. Comply with all

ventilation regulations.

Establish the gas supply using a permanent, non-

elastic connection, such as a gas pipe or a flexible

safety gas hose.

If a flexible safety gas hose is used, ensure that the

hose is not jammed or squeezed. Keep the hose

away from hot surfaces.

On some appliances, you can connect the gas pipe

to the gas pipe or flexible safety gas hose on the

right-hand or the left-hand side of the appliance. If

necessary, you can change the connection side.

The connection must have a free-standing and eas-

ily accessible locking device.

Target appliance operating pressure

You can find the target operating pressure for your

appliance on the rating plate on the rear of the ap-

pliance.

All the data on your appliance's rating plate relates

to these pressure values.

The manufacturer is not responsible for results, per-

formance or any risk caused by operating the appli-

ance at different values.

WARNING ‒ Risk of explosion!

Escaping gas may cause an explosion. If the gas pres-

sure in your distributing pipes is more than 20% higher

than the values specified on the appliance's rating

plate, a gas leak can occur.

▶

For your own safety, it is imperative that you operate

the appliance with a suitable gas governor.

▶

If you do not know what the gas pressure in your

gas distributing pipes is, please ask your local gas

company.

▶

Connection, maintenance and setting of the gas

governor must be carried out by an authorised in-

stallation specialist.

A gas leak could occur. If you move the appliance after

the gas supply has been established, a gas leak could

occur.

▶

Do not move the appliance once the gas supply is

connected.

▶

If you move the appliance, check that the connec-

tions are not leaking.

4.2 Electrical connection

The appliance must be connected by an authorised

specialist. You must comply with the requirements of

your electricity supplier.

Your appliance is designed to operate at 220–

240 V. A 16 A fuse is required for connection.

If the electricity supply drops below 180 V, the elec-

trical ignition system does not work.

If the power cord of this appliance is damaged, it

must be replaced by the manufacturer, the manufac-

turer's Customer Service or a similarly qualified per-

son in order to prevent any risk.

Any damage arising from the appliance being con-

nected incorrectly will invalidate the warranty.

Information on electrical connection by our customer

service:

Connect the appliance in accordance with the spe-

cifications on the rating plate.

The appliance must only be connected to an elec-

trical connection that corresponds to the applicable

regulations. The socket must be easily accessible

so that you can disconnect the appliance from the

electricity supply if necessary.

Ensure that a multi-pin disconnecting system is

available.

For safety reasons, this appliance must only be con-

nected to an earthed connection. If the safety earth

terminal does not comply with regulations, protec-

tion against electrical risks is not guaranteed.

To connect the appliance, use H 05 VV-F cables or

other equivalent cables.

Important information about the electrical

connection

Note the following information and ensure that:

WARNING ‒ Risk of electric shock!

There is a risk of electric shock if you touch live com-

ponents.

▶

Hold the mains plug with dry hands only.

▶

Never pull out the mains plug from the socket while

the appliance is in operation.

▶

Pull out the power cable directly at the plug and

never by pulling the power cable as this may be-

come damaged.

Fit the mains plug and socket together.

The mains plug can be accessed at all times.

The cross section of the cable is sufficient.

The mains cable is not kinked, crushed, modified or

severed.

If required, the mains cable must only be replaced

by a qualified electrician. A replacement mains

cable is available from the after-sales service.

Содержание HG 120B Series









































Результаты поиска

Содержание HG 120B Series

Отзывы:

Похожие инструкции для HG 120B Series

Бренды по названию

Популярные бренды

Bosch HG 120B Series, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание HG 120B Series

Отзывы:

Похожие инструкции для HG 120B Series

Бренды по названию

Популярные бренды