10
| English
1 609 92A 2CA | (26.2.16)
Bosch Power Tools
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note:
After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section “After-
sales Service and Application Service”.
Protection Guard for Grinding
Release the clamping lever
8
. Place the protection guard
6
with the encoding key
7
engaging into the groove on the spin-
dle collar until the shoulder of the protection guard is seated
against the flange of the power tool, and turn the protection
guard
6
to the requested position. Lock the clamping lever
8
.
Adjust the protection guard 6 in such a manner that
sparking is prevented in the direction of the operator.
The tightening tension of the clamp from the protection guard
6
can be changed by loosening or tightening the adjustment
screw
9
. Ensure that the protection guard
6
is tightly seated
and check regularly.
Note:
The encoding keys on the protection guard
6
ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting
14
is mounted in the same
manner as the protection guard for grinding
6
.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard
25
is
mounted in the same manner as the protection guard for
grinding
6
.
Auxiliary Handle
Operate your machine only with the auxiliary handle 4.
Screw the auxiliary handle
4
on the right or left of the machine
head depending on the working method.
Vibration Damper
The integrated vibration damper reduces occurring vibra-
tions.
Do not continue to use the power tool when the damp-
ing element is damaged.
Hand Guard
For operations with the rubber sanding plate 21 or with
the cup brush/wheel brush/flap disc, always mount the
hand guard 19.
The hand guard
19
is fastened with the auxiliary handle
4
.
Mounting the Grinding Tools
Before any work on the machine itself, pull the mains
plug.
Do not touch grinding and cutting discs before they
have cooled down.
The discs can become very hot while
working.
Angle Grinder
GWS ...
24-230
LV
24-230
LVJ
24-180
LVI
24-230
LVI
26-230
LVI
Article number
3 601 ...
H93 G..
H93 J..
H92 F..
H92 H..
H93 F..
H93 H..
H95 F..
H95 H..
Rated power input
W
2400
2400
2400
2400
2600
Output power
W
1600
1600
1600
1600
1650
Rated speed
min
-1
6600
6600
8500
6600
6600
Grinding disc diameter, max.
mm
230
230
180
230
230
Thread of grinder spindle
M 14
M 14
M 14
M 14
M 14
Thread length (max.) of grinder spindle
mm
25
25
25
25
25
Kickback stop
–
–
Restarting Protection
–
Reduced starting current
–
Rotatable main handle
Weight according to EPTA-Procedure 01:2014
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
5.4
5.3
5.5
5.4
5.4
5.3
5.5
5.4
5.6
5.5
Protection class
/
II
/
II
/
II
/
II
/
II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
OBJ_BUCH-1125-005.book Page 10 Friday, February 26, 2016 11:29 AM
