-25-
Shock-warning function is switched
on.
Shock-warning function is switched
on at reduced sensitivity.
Shock-warning function is switched
off.
Briefly press the on/off button
(11) to adjust the shock-warning
function setting. Then press the
on/off button (11) in the menu
which appears as often as needed
until the required setting has been selected.
Confirm your selection with by pressing the
slope button (14).
If the shock-warning function has been
switched on, it will be activated after approxi-
mately 30 seconds.
Slope operation in the horizontal position
In the laser level’s horizontal position, the X-
axis and the Y-axis can be tilted independently
of each other in a range of ±8.5%.
To tilt the X-axis, press the slope
button (14) on the laser level or
the slope button (32) on the re-
mote control once. The menu for
setting the slope of the X-axis will appear.
Set the required slope by using the buttons
▲ (4) or ▼ (3) on the laser level or using the
up (31) or down (36) slope buttons on the
remote control. Pressing both slope buttons
on the laser level or on the remote control at
the same time resets the slope back to 0.00%.
To tilt the Y-axis, press the slope
button (14) on the laser level or
the slope button (32) on the re-
mote control again. The menu for
setting the slope of the Y-axis will appear.
Set the required slope in the same way as out-
lined for the X-axis.
The selected slope is implemented
on the laser level a few seconds af-
ter the last press of a button. Both
the laser beam and the symbol for
setting slope on the display will flash until the
process of setting slope has been completed.
After the process of setting the
slope has been completed, the
set slope values of both axes will
be shown on the start screen. The
status indicator (12) on the laser level will
light up red continuously. On the remote con-
trol, the status indicator for the tilted axes
((35) and/or (34)) will light up red continu-
ously.
Slope memory for slope operation in
horizontal position
The laser level saves the four most recently
used slope values of both axes. As an alterna-
tive when readjusting the slopes, you can ap-
ply these saved slope combinations.
Start the slope operation for the X-axis (see
“Slope operation in the horizontal position”,
page 25).
To call up the slope memory,
press the line operation but-
ton (5) on the laser level or
the line operation button
(28) on the remote control.
To select one of the four
saved combinations, press
the line operation button (5)
on the laser level or the line
operation button (28) on
the remote control as many
times as needed until the
required combination is in-
dicated on the display.
Confirm the selection by pressing the slope
button (14) on the laser level or the slope
button (31) on the remote control. The slope
combination is implemented on the laser level
a few seconds after the button is pressed (see
“Slope operation in the horizontal position”,
page 25).
To set a value other than one of those saved,
press the ▲ button (4) on the laser level or the
slope up button (30) on the remote control.
The indicator returns to the slope operation
settings menu (see “Slope operation in the
horizontal position”, page 25).
SlopeProtect
Temperature changes in the laser level can
have effects on the set slope of the axes.
To avoid measurement inaccuracies, the slope
of the axes is readjusted when exceeding the
set temperature difference. The laser level is
leveled in, then it returns to slope operation
with the previously set values.
The slope is reset at temperature changes of
≥5 °C.
Using the Bosch Leveling Remote App, the
temperature difference can be lowered to 2 °C
or the SlopeProtect function can be switched
GRL4000-90CHVG 10-21.indd 25
10/20/21 3:24 PM