28
| English
1 609 92A 0XH | (12.12.14)
Bosch Power Tools
Aligning the Angle Indicator (Horizontally) (see figure N)
– Bring the power tool into the working position.
– Turn the saw table
6
to the 0° detent
11
. The lever
9
must
be felt to engage in the detent.
Checking:
The angle indicator
10
must be in alignment with the 0° mark
of the scale
12
.
Adjusting:
– Loosen the screw
43
with the cross-head screwdriver pro-
vided and align the angle indicator along the 0° mark.
– Retighten the screw again.
Aligning the Angle Indicator (Vertically) (see figure O)
– Bring the power tool into the working position.
– Turn the saw table
6
to the 0° detent
11
. The lever
9
must
be felt to engage in the detent.
– Tilt the tool arm until it faces against the stop screw
27
for
the 0° bevel angle and then tighten the clamping lever
19
again.
Checking:
The angle indicator
41
must be in alignment with the 0° mark
of the scale
44
.
Adjusting:
– Loosen the screw
45
with the cross-head screwdriver pro-
vided and align the angle indicator along the 0° mark.
– Retighten the screw again.
– Afterwards, check to ensure that the adjustment made is
correct for the 45° mark.
Aligning the Fence
– Bring the machine into the transport position.
– Turn the saw table
6
to the 0° detent
11
. The lever
9
must
be felt to engage in the detent.
Checking:
(see figure P1)
– Adjust an angle gauge to 90° and position it flush with the
saw blade
36
between the fence
5
and the saw blade on
the saw table
6
.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting:
(see figure P2)
– Loosen all hex socket screws
29
with the hex key
28
pro-
vided.
– Turn the fence
5
until the angle gauge is flush over the com-
plete length.
– Retighten the screws again.
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the machine into the transport position.
– Turn the saw table
6
until it engages at 0°.
Checking:
(see figure Q1)
– Set an angle gauge to 90° and place it on the saw table
6
.
The leg of the angle gauge must be flush with the saw blade
36
over the complete length.
Adjusting:
(see figure Q2)
– Loosen the lock lever
19
.
– Loosen the lock nut of the stop screw
27
using a commer-
cial box-end or open-end spanner (size 13 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever
19
again.
– Afterwards, retighten the lock nut of the stop screw
27
again.
In case the angle indicator
41
is not in a line with the 0° mark
of the scale
44
after the adjustment, loosen the screw
45
us-
ing a commercial cross-head screwdriver and align the angle
indicator along the 0° mark.
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the working position.
– Turn the saw table
6
until it engages at 0°.
– Loosen the lock lever
19
and tilt the tool arm leftward to
the stop (45°) by the handle
2
.
Checking:
(see figure R1)
– Set an angle gauge to 45° and place it on the saw table
6
.
The leg of the angle gauge must be flush with the saw blade
36
over the complete length.
Adjusting:
(see figure R2)
– Loosen the lock nut of the stop screw
18
using a commer-
cial box-end or open-end spanner (size 13 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever
19
again.
– Afterwards, retighten the lock nut of the stop screw
18
again.
In case the angle indicator
41
is not in a line with the 45° mark
of the scale
44
, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Transport
Before transporting the power tool, the following steps must
be carried out:
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Carry the machine by the transport handle
23
or hold it by
the recessed handles
15
on the sides of the saw table.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
OBJ_BUCH-1156-002.book Page 28 Friday, December 12, 2014 10:16 AM
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
