Bosch FWI-270 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 54

background image

8

en | Safety

Radio gateway

2019.10 | 2.0 | F.01U.373.488

Operation Manual

Bosch Sicherheitssysteme GmbH

Wrong battery types and improper battery changing lead to a risk of explosion. Only use the
same battery type or an equivalent battery type recommended by Bosch.
Batteries must be disposed of in an environmentally friendly manner. Observe national
guidelines and regulations.

Disregard of the safety regulations

Before they are delivered, Bosch products are tested to ensure they function correctly when
used properly. Bosch disclaims all liability for damage or injuries caused by the incorrect
application of the instructions or the disregard of danger warnings contained in the
documentation. This applies in particular to the following damage:
–

Personal injuries or damage to property caused by improper use and incorrect
application.

–

Personal injuries or damage to property caused by disregarding safety instructions in the
documentation or on the product.

–

Personal injury or damage to property caused by poor maintenance or lack of
maintenance.

2.3

General safety instructions

Danger!

Remove the auxiliary power supply if you want to connect FDUZ227 MCL-USB adapter radio
to the gateway!

Caution!

Electrostatic discharge (ESD)! Electronic components could become damaged. Ground
yourself using a wrist strap or take other suitable actions.

!

Caution!

Use only the lithium battery pack as specified in the accessories (order number

BAT3.6-10

).

Notice!

Batteries are not included in the scope of delivery. A battery pack is always needed to
commission and operate the radio gateway.

Notice!

Electrical data for the built-in short circuit isolator according to EN 54-17:2005, you find in
F.01U.003.287 FLM-I 420-S Installation Guide.

Notice!

Ensure that your operating system is up-to-date (updates, patches, firewall etc.) when using
the FXS2061-O Wireless diagnostic tool.

«
...
6
7
8
9
10
...
»

Содержание FWI-270























































Отзывы:

Нет отзывов

Похожие инструкции для FWI-270

Бренд: Patton Страницы: 181

SentryPlus Alert

Бренд: Watts Страницы: 12

Бренд: Farfisa Страницы: 12

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 383

926 Gateway Light

Бренд: Midas Страницы: 10

Бренд: Softing Страницы: 4

Бренд: Meraki Страницы: 11

RouteFinder RF550VPN

Бренд: Multi-Tech Страницы: 76

Бренд: TEKTELIC Communications Страницы: 34

Бренд: daviteq Страницы: 14

Бренд: Planet Networking & Communication Страницы: 61

Бренд: Technicolor Страницы: 103

OfficeConnect 3CRWE53172

Бренд: 3Com Страницы: 124

OCG VOICE EXPANSION -

Бренд: 3Com Страницы: 177

Бренд: Dwyer Instruments Страницы: 4

Бренд: ZyXEL Communications Страницы: 2

Бренд: Soma Networks Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды