Bosch FLEXIDOME indoor 5100i Скачать руководство пользователя

Страница: 39 / 56

FLEXIDOME indoor 5100i (IR) | FLEXIDOME
outdoor 5100i (IR)

Configuration | en

Bosch Security Systems B.V.

User manual

11-2022 | V02 | F.01U.394.427

Recording

Identifies the current recording profile (1 or 2).

Zoom

Identifies the current zoom factor of the camera (1x, 2x, 4x, or 8x).

Averaging period

Select the appropriate averaging period as a means of stabilizing the long term bit rate.

4.5.7

Image Posting

Save individual JPEG images on an FTP server at specific intervals.

JPEG

Image size

Select the size of the JPEG images that are to be sent from the camera. JPEG resolution
corresponds to the highest setting from the two data streams.

File name

Select how file names are created for the individual images that are transmitted.
–

Overwrite

: The same file name is always used and any existing file will be overwritten by

the current file.

–

Increment

: A number from 000 to 255 is added to the file name and automatically

incremented by 1. When it reaches 255, it starts again from 000.

–

Date/time suffix

: The date and time are automatically added to the file name. When

setting this parameter, make sure that the date and time of the device are always set
correctly. For example, the file snap011005_114530.jpg was stored on October 1, 2005 at
11:45 and 30 seconds.

VCA overlays

If you have enabled the display of VCA overlays on the

Appearance

page, select the

VCA

overlays

check box to have the overlays also visible in the JPEG image.

Posting interval

Enter the interval in seconds at which the images are sent to an FTP server. Enter zero for no
images to be sent.

Target

Select the target account for JPEG posting.

Notice!

You must configure an account in order to have functionality for

Image Posting

. Click on

Configure accounts

to do so.

Click

Set

to apply the changes.

4.5.8

SD Card Status

This section identifies the details about the SD card installed in the device:
–

Manufacturer

–

Product

–

Size

–

State

–

Lifespan

Lifespan check

When checked, the

Lifespan

status is shown in the details of the SD cards.

Lifespan alarm

Содержание FLEXIDOME indoor 5100i

























































Результаты поиска

Содержание FLEXIDOME indoor 5100i

Отзывы:

Похожие инструкции для FLEXIDOME indoor 5100i

Бренды по названию

Популярные бренды

Bosch FLEXIDOME indoor 5100i, Руководство пользователя

Результаты поиска

Содержание FLEXIDOME indoor 5100i

Отзывы:

Похожие инструкции для FLEXIDOME indoor 5100i

Бренды по названию

Популярные бренды