manualshive.com logo in svg

Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20, Руководство по установке

Поделиться
Скачать
Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20 Скачать руководство пользователя страница 10

8

en | Configuration through the Web Interface

DSDA iSCSI Disk Array Series

V 1 | 2008.08

Installation Guide

Bosch Security Systems

5

Configuration through the Web Interface

Follow these steps to configure each system. This procedure is nearly identical for all three 

types of storage systems. 

1.

Turn on the system.

DSA-S5B50

: The power button is located on the front side on the left-hand side.

DSA-N2B20

 / 

DSA- N2B50 

/

 additional disk shelves

: There is a power switch on each 

power supply unit (right- and left-hand side) on the rear side of the device.

If there are additional disk shelves installed, first power on the base unit, then power on 

the expansion units.

5.1

Configuration of the Network Settings and Access to the 
Interface

All systems are delivered with a default IP address configuration of 10.10.10.10, netmask 

255.0.0.0. In order to connect to the system, you need to configure a network interface on 

your computer to use the same network. 

i

NOTICE! 

Do not use the S5B50 management software StoreVault Manager for the configuration. The 

DSA series come with a dedicated Bosch standardized system layout. StoreVault Manager is 

not compatible with the Bosch layout.

i

NOTICE! 

It can take a few seconds until the LEDs on your system power supplies light up.

i

NOTICE! 

The Java Runtime Environment must be installed on your computer in order to use the Web  

interface. Always use the most recent version.

Содержание DSDA ISCSI DISK ARRAY SERIES DSA-N2B20









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды