Bosch CLC6001i 25 E Скачать руководство пользователя

Страница: 23 / 120

4-3

Climate Class 6100i / 6000i / 8100i / 8000i

[2] AIR CONDITIONER OPERATION IN THERMISTOR ERROR

* These models have following thermistors

INDOOR UNIT

OUTDOOR UNIT

TH1, TH2

TH1, TH2, TH3, TH4, TH5

The errors for the thermistors that are not mentioned above are irrelevant.
These indoor units don’t have power relay.
These models don’t have Heating operation.

1.Indoor unit

Item

Mode

Control opera-

tion

When resistance

is low (tem-

perature judged

higher than

actual)

Short-circuit

When resistance

is high (tem-

perature judged

lower than actu-

al)

Open-circuit

Room tempera-

ture thermistor

(TH1)

Auto

Operation mode

judgment

Cooling mode is

activated even if

room temperature

is low.

Cooling mode is activat-

ed in most cases.

Heating mode is

activated even if

room temperature

is high.

Heating mode is

always activated.

Cooling

Frequency con-

trol

Room becomes

too cold.

Air to air conditioner

operates in full power

even when set tempera-

ture is reached.

Room does not

become cool.

Compressor does not

operate.

Dehumidifying

Room tempera-

ture memory

Frequency con-

trol

Normal operation. Room temperature is

stored in memory as

31.0°C, and compressor

does not stop.

Normal operation. Room temperature is

stored in memory as

18.5°C, and compres-

sor does not operate.

Heating

Frequency con-

trol

Room does not

become warm.

Hot keep status results

immediately after opera-

tion starts.

Frequency does not

increase above

30 Hz (40 Hz).

Room becomes

too warm.

Air conditioner oper-

ates in full power even

when set temperature

is reached.

Heat exchanger

thermistor (TH2)

Cooling

Dehumidifying

Freeze preven-

tion

Indoor unit

evaporator may

freeze.

Indoor unit evaporator

may freeze.

Compressor

stops occasional-

ly.

Compressor does not

operate.

Heating

Cold air preven-

tion Cold

Cold air preven-

tion deactivates

too soon and cold

air discharges.

Compressor operates

at low speed or stops,

and frequency does not

increase.

Cold air preven-

tion deactivates

too slow.

Cold air prevention

does not deactivate,

and indoor unit fan

does not rotate.

2.Outdoor unit

Item

Mode

Control opera-

tion

When resistance is

low (temperature

judged higher than

actual)

Short-circuit

When resistance is

high (temperature

judged lower than

actual)

Open-circuit

Compressor

discharge

thermistor

(TH1)

Cooling

Dehumidifying

Heating

Expansion valve

control and com-

pressor protec-

tion

Compressor operates,

but room does not

become cool or warm

(expansion valve is

open).

Compressor high

temperature error

indication.

Layer short-circuit

or open-circuit may

result in compressor

in normal operation.

Outdoor unit therm-

istor open-circuit

error indication.

Heat exchanger

thermistor (TH2)

Cooling

Dehumidifying

Outdoor unit heat

exchanger over-

heat prevention

Compressor operates

at low speed or stops.

Outdoor unit

thermistor

short-circuit error

indication.

Normal operation.

Outdoor unit therm-

istor open-circuit

error indication.

Heating

Expansion valve

control Defrost-

ing

Defrosting operation

is not activated as

needed, and frost ac-

cumulates on outdoor

unit (expansion valve is

closed).

Outdoor unit

thermistor

short-circuit error

indication.

Defrosting operation

is activated unnec-

essarily, and room

does not become

warm (expansion

valve is open).

Outdoor unit therm-

istor open-circuit

error indication.

Содержание CLC6001i 25 E

























































































































Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды

Bosch CLC6001i 25 E, Руководство по обслуживанию

Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды