Bosch CLC6001i 25 E Скачать руководство пользователя

Страница: 16 / 120

3-2

Climate Class 6100i / 6000i / 8100i / 8000i

• Full power setting
• Self cleaning
• Multi Space setting
• ECO setting

3) Disabling auto restart function

By removing (cutting) jumper (JP0) on the printed circuit board(PCB), the auto restart function can be disabled.

12. Save operation

This control is valid only in AUTO mode.

In addition, Average models (CLC6001i-W 25/35 E, CLC8001i-W 25/35 E(T/S/R)) only when ECO mode is enabled. Nordic models (CLC6101i-W

50/65 HE, CLC8101i-W 65 HE(T/S/R)) only when another mode is disabled.

If there is no person for 1 hour, the air conditioner will arise setting temperature.
If a person is detected, correction temperature will be restored.

13. Activity Detection

This control is valid only in AUTO mode. If the amount of human activity increases for few minutes, setting temperature is lowered, fan rotation is

increased by 100rpm when fan setting is AUTO, and horizontal louver (H-louver) is turned downward when the louver setting is AUTO. If a person’s

activity decreases, it is returned to original state.
Setting temperature is corrected lower by the amount of human activity as following.

temperature correction table temperature correction degree

activity weak activity mid

activity strong

room

temperature(°C)

29/30

1.75

2.5

27/28

1.5

25/26

0.5

1.5

23/24

0.25

0.75

1.25

17~22

0.25

0.5

0.75

Содержание CLC6001i 25 E

























































































































Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды

Bosch CLC6001i 25 E, Руководство по обслуживанию

Результаты поиска

Содержание CLC6001i 25 E

Отзывы:

Похожие инструкции для CLC6001i 25 E

Бренды по названию

Популярные бренды