Bosch B465 Скачать руководство пользователя страница 74

Страница: 74 / 115

en | System Configuration

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

Notice!
UL 864 requirement for commercial fire

To comply with UL864 requirements for commercial fire systems, set this parameter to

Enabled

USB Menu Location

[4] System Configuration > [3] Battery Supervision > [1] Battery Monitoring

8.3.2

Battery faults send reports

Default

Enabled

Selections

–

Enabled - the B465 sends reports for low and missing battery faults.

–

Disabled - the B465 does not send reports for battery faults.

Notice!
UL 864 requirement for commercial fire

To comply with UL864 requirements for commercial fire systems, set this parameter to

Enabled

USB Menu Location

[4] System Configuration > [3] Battery Supervision > [2] Battery faults send reports

8.3.3

Battery faults set Trouble Output

Default

Disabled

Selections

–

Enabled - when there is a battery fault, the B465 sets the trouble output.

–

Disabled - the B465 does not set the trouble output for battery faults.

USB Menu Location

[4] System Configuration > [3] Battery Supervision > [3] Battery faults set Trouble Output

8.4

Tamper

Use the parameters in this section to configure the B465 to monitor an enclosure tamper
switch.

8.4.1

Tamper sends reports

Default

Disabled

Selections

–

Enabled - the B465 sends reports and sets the trouble LED for faults on the tamper
circuit.

–

Disabled - the B465 does not send reports or set the trouble LED for faults on the tamper
circuit.

When an enclosure tamper switch is connected to the B465 tamper circuit (TMPR connector),
opening the enclosure door is a fault.

USB Menu Location

[4] System Configuration > [4] Tamper > [1] Tamper sends reports

8.4.2

Tamper sets Trouble Output

Default

Disabled

Selections

–

Enabled - when there is a fault on the tamper circuit, the B465 sets the trouble output.

–

Disabled - the B465 does not set the trouble output for faults on the tamper circuit.

Содержание B465




















































































































Результаты поиска

Содержание B465

Отзывы:

Bosch B465, Инструкция по установке и эксплуатации, Страница: 74 / 115

Результаты поиска

Содержание B465

Отзывы: