manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Руководство по установке, Страница: 35 / 92

Поделиться
Скачать
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Скачать руководство пользователя страница 35

AMAX panel 2000 / AMAX panel 2000 EN

 Fault and Tamper Description | en

35

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault

5.5

Date and Time Fail 

Condition:

Date and time is not set after the system is powered on.

Restore:

Date and time is programmed and the fault is reset. Refer to Section 3.1.1 Setting date and 

time for more information.

Supervise:

1.

No report on the date and time fault.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators)

3.

No report to the control panel system when date and time setting is recorded in non-

volatile memory and Control Panel is reset. The FAULT indicator is turned off when there 

is no other system fault.

5.6

Communication Failure 

The zone indicator 6 lights to indicate Communication Failure. Enter [6] to step to 

Communication failure list for more information.

5.6.1

Communication Failure 1

Condition:

Panel can not send the report to the Destination 1 after 4 attempts.

Restore:

The fault is reset when the first kissoff tone is received and fault is reset.

Supervise:

1.

Report the fault to configured destination on location 140 when the fault is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.6.2

Communication Failure 2

Condition:

Panel can not send the report to the Destination 2 after 4 attempts.

Restore:

The fault is reset when the first kissoff tone is received and fault is reset.

Supervise:

1.

Report the fault to configured destination on location 140 when the fault is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.6.3

Communication Failure 3

Condition:

Panel can not send the report to the Destination 3 after 4 attempts.

Restore:

Содержание AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Отзывы:

Нет отзывов