manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Руководство по установке, Страница: 33 / 92

Поделиться
Скачать
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Скачать руководство пользователя страница 33

AMAX panel 2000 / AMAX panel 2000 EN

 Fault and Tamper Description | en

33

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the AUX power fault to the configured destination programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.2.4

Bosch Option Bus Power Supply Fail 

Condition:

Bosch option bus power supply Voltage is lower than 9V+-5%.

Restore:

Voltage is raised to 12.5V+-5% and fault is reset.

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the Bosch Option Bus Power Supply fault to the configured destination 

programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.2.5

RF Power Supply Fail 

Condition:

Voltage is lower than 4V+-5%.

Restore: 

Voltage is raised to 5.5V+-5% and fault is reset.

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the RF power fault to the configured destination programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.3

Warning Device Failure 

The zone indicator 3 lights to indicate Warning Device Failure. Enter [3] to step to external 

modules fail list for more information.

5.3.1

Warning Device 1 Disconnected 

Condition:

Warning Device is disconnected.

Restore:

Warning Device is connected and fault is reset.

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the siren fault to the configured destination programmed on location 140

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

Содержание AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Отзывы:

Нет отзывов