Bosch ABS M4 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 54

Bosch ABS M4 Скачать руководство пользователя страница 24

Laptop Communication

The MSA Box II from Bosch Motorsport is the communication interface between
ABS M4 and the programming and diagnostic software on your laptop.

Installing the MSA Box II driver:

Before using the MSA Box II for the first time, you need to install a specific driver
on your laptop. Find the driver for free download on our website www.bosch‐
motorsport.de.

Notice

Please make sure that the MSA Box II is not connected to the
laptop while you are installing the driver.

Connect the MSA Box II to the laptop after installing the driver. This will trigger
the initial communication between the laptop and the MSA Box II. Follow any
prompts that may follow to install the MSA Box II. Once you complete any
prompts and computer recognizes the MSA Box II, the MSA Box II is ready for
use.
Steps:
1. Unplug the MSA Box II from the laptop.
2. Install the driver.
3. Plug the MSA Box II into the laptop.
You can connect ABS M4 to a laptop with the MSA Box II via the "diagnosis inter‐
face" connector. The diagnosis interface connector should be placed so it is easi‐
ly accessible. You can use programming and diagnosis software, see section Pro‐
gramming and Diagnosis Software, to program settings specific to the vehicle
and open/delete error messages.

8

8 | Laptop Communication

24 / 54

ABS M4 Manual

Bosch Motorsport

«
...
22
23
24
25
26
...
»

Содержание ABS M4























































Отзывы:

Нет отзывов