Bosch 3 601 JH6 0, Оригинальное руководство пользователя, Страница: 29 / 459

English | 29
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Kickback stop
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically. The kickback stop indicator
(32)
then lights up. When kickback stop is activ-
ated, the status indicator (36) flashes red.
To restart the tool, set the on/off switch (5) to the off posi-
tion and then switch the power tool on again.
Restart protection
The restart protection feature prevents the power tool from
starting unintentionally after the power supply to it has been
interrupted.
When restart protection is activated, the status indicator
(36) flashes red.
To restart the tool, set the on/off switch (5) to the off posi-
tion and then switch the power tool on again.
Impact shutdown
The integrated impact shutdown switches the power tool off
as soon as it hits the floor. The status indicator
(36) then
flashes red.
To
restart the tool, set the on/off switch (5) to the off posi-
tion and then switch the power tool on again.
User interface (see figure D)
The user interface (4) is used to preselect the speed and to
indicate the status of the power tool.
Speed Preselection (GWS 18V-15 SC)
In the default setting, 3 speed levels are preset. A special application (Bosch Toolbox App) can be used to program up to 6
speed levels.
If the number of speed levels is changed, the values of the individual levels are adjusted by default. In this case, the speed
level/mode indicator
(34) lights up white. When a speed value is programmed individually, the speed level/mode indicator
(34) lights up blue at this speed level (i.e. not according to a default setting). The individual adaptation of speed levels is pos-
sible in steps of 200 rpm each. Observe the ascending logic of the steps (2 ≥ 1 / 3 ≥ 2 etc).
The information in the tables below describes the preset speeds (default settings) for each programmed number of levels.
GWS 18V-15 SC
(115/125 mm) Basic speed setting at level
1 2 3 4 5 6
[min
-1
] [min
-1
] [min
-1
] [min
-1
] [min
-1
] [min
-1
]
Number of speed settings
1 3400 – – – – –
2 3400 max. – – – –
3 3400 6600 max. – – –
4 3400 5600 7600 max. – –
5 3400 5000 6600 8200 max. –
6 3400 4800 6000 7200 8600 max.
GWS 18V-15 SC
(150 mm) Basic speed setting at level
1 2 3 4 5 6
[min
-1
] [min
-1
] [min
-1
] [min
-1
] [min
-1
] [min
-1
]
Number of speed settings
1 2600 – – – – –
2 2600 max. – – – –
3 2600 5000 max. – – –
4 2600 4200 5800 max. – –
5 2600 3800 5000 6200 max. –
6 2600 3600 4600 5400 6400 max.
You can use the button for speed preselection (33) to preselect the required speed, even during operation. The information in
the table below describes the recommended values for the default settings with 3 preset speed levels.
Bosch Power Tools 1 609 92A 4GB | (11.07.2019)